Audio Asylum Thread Printer

Get a view of an entire thread on one page

FAQ / News / Events

Tweakers' Asylum

RE: You would still have a ground loop.

70.56.4.35

In Reply to: RE: You would still have a ground loop. posted by Pooge on July 04, 2007 at 14:26:42

Here are the facts, as we know them:
The wiring,
* One truly dedicated 120V branch circuit. Consisting of one each dedicated, hot conductor, neutral conductor, and equipment grounding conductor.
* Two separate 120V circuits. A 3 wire multi wire branch circuit consisting of two hot conductors (each connected to a breaker fed from each Line in the electrical panel L1 and L2). One shared neutral conductor, and one shared equipment grounding conductor.
* The truly dedicated circuit feeds the preamp and what ever source equipment.
* The two separate circuits,
if a power amp is feed from each separate 120V circuit a hum is heard through the speakers.
Note..... There is only one equipment grounding conductor for both circuits feeding the power amps....
Added note, at idle both amps theoretically are drawing the same amount of current so the two power transformers primary windings are in series with one another and being fed by a difference of potential of 240 volts nominal.
* If both power amps are plugged into only one of the separate circuits, that circuit being fed from the same Line in the electrical panel as the truly dedicated circuit, the final result, no hum is heard through the speakers.
*Still the same equipment grounding conductor.

* Why no hum??

Edits: 07/04/07

Follow Ups:

RE: You would still have a ground loop. - Pooge 17:27:16 07/04/07 (5)
Difficult to say without more diagnosis. First I would disconnect the preamp cables from the power amps. Then I would try the power amps in both power supply connections to see if one still hums more than the other. If, for example, it still hums in the three-wire two-circuit mode, I would suspect transformer leakage adding into the ground line instead of cancelling. It may be that a reversal of the transformer leads in one of the amps would correct this. (Don't do this with the power line, since the hot should go through the switch.) It may also be that one circuit is providing a ground loop for the other through the common ground.

If both power arrangements work with no noise when not connected to preamp, then there is probably a ground loop situation that the preamp brings when connected.
- RE: You would still have a ground loop. - jea48 07:14:55 07/05/07 (3)
  Difficult to say without more diagnosis. First I would disconnect the preamp cables from the power amps.
  
  > > > > > > > > > > > > > > >
  
  I believe in one of Steve's earlier posts he did disconnect the ics from the preamp and the two amps. No hum with the ics disconnected.
  ---------------
  
  I would be curious what the effect, result, would be if Steve left the ics connected to the preamp but unplug the preamp from the 120V power outlet. Also disconnect all input ics from the preamp.
  
  This test would still have the two power amps signal ground tied together at the preamp jacks. Would there still be a hum?
  Your thoughts, or Al's, or any one else's.......
  - We also know that Steve's setup with two AC circuits does not hum. - Al Sekela 15:59:03 07/05/07 (2)
    The preamp circuit and the power amp circuit have separate safety-earth wires that go back to the circuit breaker panel. According to Steve, this setup, with both monoblocks fed from one hot wire, does not hum.
    
    Therefore the use of the second hot wire for one monoblock is the proximate cause of the hum. Whether it is because of the small residual current in the neutral wire, or mismatched power transformer parasitic capacitances, would have to be determined by some simple experiments and measurements.
    - Agree... - jea48 06:05:22 07/06/07 (1)
      Therefore the use of the second hot wire for one monoblock is the proximate cause of the hum. Whether it is because of the small residual current in the neutral wire, or mismatched power transformer parasitic capacitances, would have to be determined by some simple experiments and measurements.
      
      > > > > > > > > > > > > >
      
      How about this for a test, have Steve plug one of the power amps into the dedicated circuit with the preamp. Leave the other amp plugged into the separate circuit outlet that is on the same Line, leg, as the preamp recept.
      
      We would have all the audio equipment being fed from the same Line, leg, of the electrical panel. Will there be a hum?
      ----------------------
      
      I wonder how many guys out there think they had two dedicated circuits installed by an electrician for the audio equipment, and instead have two separate circuits.......
      - Good experiment. - Al Sekela 13:31:32 07/06/07 (0)
        
        In Reply to: RE: Agree... posted by jea48 on July 06, 2007 at 06:05:22
        
        If there is hum with this configuration, then it is time to check the individual amp power transformers.
- RE: You would still have a ground loop. - Pooge 17:42:55 07/04/07 (0)
  I should add that reversing the transformer leads to correct this might only be a bandaid approach for this particular power circuit arrangement. It may compromise the noise in a normal arrangement.
  
  Tranformers have a different leakage capacitance from each side of a winding and ground. Therefore, one lead orientation will couple a different amount of noise to ground than the opposite lead arrangement. This is why reversing the plug may sound better one way than the other. To test for this, disconnect the PC ground from the chassis. Power up, and measure the voltage between the disconnected PC ground line and chassis. Shut off, reverse transformer leads, and measure voltage between the disconnected PC ground line and chassis again. The transformer connection having the lowest voltage between the chassis and the ground line is the one to use, because less leakage will flow to ground.
  
  Hard to say if the best arrangement was done when amps were made, but perhaps putting the amps on differently phased circuits caused the leakage currents to add.
  
  I'm not entirely confident of this is the entire reason for the noise. It could also be from one circuit being a loop coupled to the other via the ground line. There's no way of telling without going through the process of elimination.

Post a Followup:

FAQ

Post a Message!

Forgot Password?

Moniker (Username):
Password (Optional):
	Remember my Moniker & Password (What's this?) Eat Me
E-Mail (Optional):
Subject:

Message:	(Posts are subject to Content Rules)

Optional Link URL:
Optional Link Title:
Optional Image URL:
Upload Image:
E-mail Replies:	Automagically notify you when someone responds.

To view your new posting or follow-up, click on the RELOAD or REFRESH button on your browser.

This post is made possible by the generous support of people like you and our sponsors: